B-Sideby RPXL

PK-01: A pocket music player

It plays FLAC and WAV from a microSD card in its port end, through a 3.5 mm headphone jack or over Bluetooth to headphones and speakers. Four keys on a column of tiles, a push wheel on the right edge, a hold slide and a 2.0 inch screen showing the cover. Record cards are an optional add-on: flat cards that each carry one album and slide into the top edge.

Size
66 × 78 × 15 mm
Screen
2.0 in colour by default. Other plates: 1.9, 1.69 and 1.47 colour, a 2.25 colour bar and a 2.08 mono OLED bar
Audio
PCM5102A board to a 3.5 mm jack, or Bluetooth (A2DP) to headphones and speakers
Music
A microSD card in the port end. Optional record cards in the top edge

Read the build manualWhat it covers

  • A column of tiles

    Four round keys, one to each tile, with a groove between the tiles. The glyphs are engraved in the caps.

  • A straight dot strip

    Two columns of small round dots are pressed into the deck beside the keys. It is one clean line, so the deck under the screen stays quiet for the mark.

  • One dark band, one screen

    The screen sits in a charcoal band on the right. A different screen is a different plate, not a different body.

  • Four black screws

    Black button heads sit flush in the deck and are the only fixings you see. Flutes run along the right edge beside the wheel and the hold slide.

  • Three plain openings

    The headphone jack, USB-C and the library microSD slot sit in the port end as round-ended openings with a small chamfer. There are no icons: the shapes say what they are.

  • Charge it over USB-C

    A small charger module fills the 1000 mAh cell from the USB-C port. In a dock, the same port is what the speaker's plug charges.

  • The library card

    Your music lives on a microSD card in a push-push slot under the USB-C. Press it in to latch it and press again to let it out.

  • Bluetooth is standard

    PK-01 streams to Bluetooth headphones and speakers on its own. Docked in the SP-01 dock speaker, it plays through the dock by itself, with no pairing for you.

Record cards, an optional add-on

The base PK-01 plays from its microSD card. Build the card reader and the slotted top edge and it also plays record cards: flat cards that each carry one album. The card slides into the top edge and ends level with it, so only its ribbed end and spine show while it plays. Give one to a friend.

Into the slot. Label toward the screen, the other end first, down a printed channel. Nothing on the card sticks out.
All the way in. The ribbed end finishes level with the top edge and the screen starts to play the album.
One card, both sides. A square cover label and a ribbed strip to grip it, and on the other side the gold pads, level with the surface. A Budget card shows its microSD through a window.
Filed by their spines. PK-01 plays a card while two more wait in a small printed rack, spine labels showing.
  • A flat card, nothing sticking out

    The card is a plain flat rectangle, 22 × 34 × 2.6 mm. Eight gold pads sit level with its underside, so a card lying on a desk never rests on them.

  • One slot, two cards

    Budget is a microSD set into a printed case, its own gold pads showing through a window. Premium is a thin card circuit board in the same case, with the art on its label. The slot reads either.

  • It only goes in one way

    A printed channel guides the card, and a small rib in the channel runs in a cut on one edge of the card, so a card turned the wrong way stops at the mouth. Printed stops end its travel with its spine level with the top edge.

  • No latch to wear out

    Eight small springs on the floor of the slot press up against the pads. Friction holds the card in place. To take it out, pinch its ribbed end between a thumb in the scoop at the front and a fingertip in the notch at the back.

  • Labels you can change

    The cover and the spine label are adhesive vinyl set flush into shallow pockets, so every card can carry your own art and track list.

  • A rack for the spines

    A small printed rack files the cards upright with their spine labels showing, like records on a shelf.

What is inside

Ready-made modules wired together, so there is no custom main board to order.

  • Brain

    An Adafruit QT Py ESP32 Pico, a classic ESP32 with Bluetooth, 8 MB of flash and USB-C.

  • Screen

    An ST7789 SPI colour module, 2.0 inch by default, in its own swappable plate.

  • Audio

    A GY-PCM5102 board feeding the 3.5 mm jack. It drives in-ear headphones directly, and there is no room for a separate amplifier.

  • Wheel and keys

    A thumbwheel encoder through the right edge, four tact switches under the caps and a hold slide, wired to the board.

  • Power

    A 1000 mAh 602560 lithium cell lying flat on the left under the keys, charged by a small USB-C charger module.

  • Library slot

    A push-push microSD socket in the port end, under the USB-C.

  • Card reader (optional)

    A strip of spring contacts lies flat under the card and presses on its gold pads. Leave it out and print a plain blank to close the slot.

You print

The shell, the deck, the screen band, the key caps and carrier, and the wheel sleeve and hold cap if you print them. With the card reader: the cards and the rack. Without it: a blank for the slot.

You buy

The QT Py ESP32 Pico, a screen module, an audio board, a charger module, a thumbwheel encoder, a cell, tact keys, M2 screws and nuts, and a microSD card for your music. Optional: a turned aluminium sleeve and a brass cap, and for record cards a reader socket and one microSD or card board per card.

You build

Wire the modules together, press the sleeve and cap on, seat the cell and the screen, and close the shell with four screws. No custom main board.

Build PK-01 your way

One printed casing, three sets of components. The face, the keys, the optional card slot and the build are the same whichever you pick.