SP-01: A pocket speaker and a dock speaker
A Bluetooth speaker in two sizes on one look: a pocket speaker for a bag and a dock speaker for the desk. The face is grille cloth held at its edge by a white silicone cord rolled into a groove like a fly screen, with no glue. A rocker on the end does volume, play and power, and four warm lights sit on top. It plays from any phone, with no app.
- Size
- Sound
- Power
- Paint and cloth
Docked, everything still works
The bay in the speaker's face holds PK-01 upright, ports down, screen toward you. It stands 36 mm proud of the top, so the wheel on its right edge clears the speaker and your thumb reaches it without touching the band. Wheel, keys, screen and hold slide all work in the bay, and its card slot faces up and stays clear, so a record card can be swapped while it plays.
- Four warm lights on top, each an end-glow fibre in its own hole.
- Rocker ends for volume, press the centre to play or pause, hold it for power.
- A plug at the bottom of the bay charges PK-01 from the speaker's USB-C input. When PK-01 senses that power it connects to the speaker over Bluetooth by itself and plays through it, with no pairing for you.
- The dock speaker is still a Bluetooth speaker for your phone.
You print
The speaker body, the back plate, the end block, the rocker and the badge, each whole with no glued seams, in a tough opaque resin. Templates for the cloth.
You buy
An Adafruit QT Py ESP32 Pico and amplifier boards, the drivers and a passive radiator, white silicone cord, grille cloth, end-glow fibre for the lights, tact switches for the rocker and M2 screws. The pocket adds a cell and a charger module. The dock speaker takes two Dayton DMA45-4 drivers, a 50 × 90 racetrack radiator, a USB-C power input and the USB-C plug for PK-01's bay, and runs from a 5 V 3 A USB-C charger.
You build
Wire the boards, seat the drivers, roll the cord in, then screw the parts together. The dock speaker also takes PK-01's bay and plug, and a sealed chamber behind the cloth.
Two sizes
Pick a size first. Both are built the same way and each has its own Budget, Mid and Premium parts.
Pocket
86 × 30 × 80 mm
One 40 mm driver and a passive radiator, a rechargeable cell and USB-C. It goes in a bag.
Dock speaker
185 × 62 × 104 mm
Stereo from two drivers side by side and a racetrack radiator, powered over USB-C, with a bay in its face for PK-01 that charges it and plays it over Bluetooth.
Build SP-01 your way
Two sizes on the same cord, cloth, rocker and four warm lights. The tiers below are the pocket speaker's components. The dock speaker has the same three tiers on one set of drivers: two Dayton DMA45-4 and a 50 × 90 racetrack radiator in every one, with the amplifier boards, cloth, fibre, feet and screws changing.
Budget
Generic driver and radiator
A generic 40 mm 4 ohm driver and a plain 50 mm passive radiator, any open-knit speaker cloth, zinc M2 screws, and the casing sanded to a satin finish instead of painted.
Mid
PUI driver, painted
A PUI Audio AS04004PR-R 40 mm driver, a clone MAX98357A amplifier board, filler primer and one painted colour with white, and a 1000 mAh cell from a bulk seller.
Premium
Adafruit amp, better cloth
An Adafruit MAX98357A amplifier board, a branded protected LiPo cell, acoustically transparent knit cloth, premium end-glow fibre, clear polycarbonate feet and stainless socket-head screws.
The SP-01 build manual
One illustrated page that follows your choices: pocket or dock speaker, Budget, Mid or Premium parts, resin or PLA. Parts with A$ costs for every tier, print and paint, wiring, firmware, the assembly steps and the screw map.
Read the SP-01 build manual