VK-01: A volume knob for your Mac
One plain knob on a printed body. Turn it to change the Mac's volume, press it to mute. It plugs in as a media keyboard, so the Mac needs no software.
- Body
- 92 × 92 mm, 43 mm to the knob top
- Knob
- 44 × 19 mm plain disc, R5 rounded top edge
- USB edition
- Arduino Leonardo, wired
- Bluetooth edition
- Seeed XIAO nRF52840 with a 1100 mAh cell
A ring of light, never an LED
Six LEDs aim up into a white chamber under the face. Light leaves only through the 1.75 mm gap round the knob, so you see a soft ring.
A mute dot that hides
One more LED sits in its own light-tight cup behind seven 0.6 mm holes. When it is off, the holes are hard to find.
Four screws hold it all
Four black M3 button heads go down through the face panel, the light deck and the upper body into nuts held captive below.
The board sits on a tray
The controller rides on its own small printed tray. A different board needs a different tray, never a different body.
Pick your knob
The deck takes four knobs without changing another part. The halo gap round the knob stays 1.75 mm for all of them.
Printed, painted
The plain 44 × 19 mm disc, printed in resin and painted the deck colour. A grub screw, a nut and a steel washer glued in underneath give it weight.
Bought, knurled
A 44 × 22 mm diamond-knurled aluminium knob with a 6 mm D bore and a grub screw. It fits the same shaft.
CNC aluminium
The same plain disc machined from 6061 aluminium, bead blasted and anodised, about 71 g. The kit gives you the file and a drawing note for a machining service.
Your own
Any knob from 25 to 40 mm across with a 6 mm D bore. Print the ring adapter for its diameter and it sits in the deck opening.
Every part, in the order it stacks
Point at a part, or at its number on the picture.
- Knobprinted and painted, bought, or CNC aluminium: D bore, grub screw
- Face screwsbought: M3 × 20 button head, black oxide
- Face panelprinted, painted charcoal
- Nut and washerbought: they clamp the encoder to the deck
- Light deckprinted, painted white inside the chamber
- Encoderbought: EC11 type with push switch
- LEDsbought: seven white 3 mm, six for the ring, one for mute
- Driver boarda perfboard offcut you solder
- Upper bodyprinted, painted white
- Controller on its traybought board, printed tray
- Port plateprinted: frames the board's own socket
- Lower bodyprinted, with captive nut pockets
Build VK-01 your way
One printed casing, three knobs. The light ring and the build are the same whichever you pick. USB or Bluetooth is a separate choice of edition.
Budget
Printed knob
The plain 44 × 19 mm knob printed in resin and painted the deck colour, with a grub screw, a nut and a steel washer glued in for weight.
Mid
Bought knurled knob
A 44 × 22 mm diamond-knurled aluminium knob from a parts seller. It fits the same shaft.
Premium
CNC aluminium knob
The plain disc machined from 6061 aluminium, bead blasted and anodised, about 71 g.
VK-01 in fourteen steps
Each kit has an illustrated manual that follows your choices. These are the fourteen steps of the USB edition, from the face nuts to the rubber feet.
You print
Lower and upper body, light deck, face panel, port plate and board tray, in a tough opaque resin. The Bluetooth edition adds a strap for the cell.
You buy
The knob, an encoder, a Leonardo or a XIAO, seven LEDs, a few resistors and a transistor, black M3 screws and nuts, and four rubber feet.
You build
Solder a small harness, flash it from the command line, then stack it up in fourteen steps. No heat-set inserts.
The VK-01 build manual
One illustrated page that follows your choices: USB or Bluetooth edition, which knob, resin or PLA. Parts with A$ costs, print setup and the light test, wiring, firmware, fifteen assembly steps with the part being fitted shown in orange, the screw map and troubleshooting.
Read the VK-01 build manual